1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  2. Ads can be a pain, but they are our only way to maintain the server. Your patience is highly appreciated and we hope our service can be worth it. but if you want buy ad-free account please click here

eMMC Pro V1.06 and a lot of new models !

Discussion in 'Hard/Software Products & Online Server' started by Abi Wyeamn, Aug 19, 2016.

  1. Abi Wyeamn

    Abi Wyeamn Well-Known Member
    Verified ✔ Registered ✔

    Jan 27, 2016
    Likes Received:
    Trophy Points:
    Huawei Mate 8
    eMMC Pro Updates
    [19 AUG 2016]

    eMMC Pro V1.06 Release Notes
    • Detecting eMMC Controls added
    • Errors and Handling
    • Writing to Fake I/O Bug is fixed.
    • Error Codes

    Error Messages and Handling ;

    CMD_CRC_FAIL                        =    (1)      which is Command response received (but CRC check failed)
    DATA_CRC_FAIL                       =    (2)      which is Data bock sent/received (CRC check Failed)
    CMD_RSP_TIMEOUT                     =    (3)      which is Command response timeout
    DATA_TIMEOUT                        =    (4)      which is Data time out
    TX_UNDERRUN                         =    (5)      which is Transmit FIFO under-run
    RX_OVERRUN                          =    (6)      which is Receive FIFO over-run
    START_BIT_ERR                       =    (7)      which is Start bit not detected on all data signals in widE bus mode
    CMD_OUT_OF_RANGE                    =    (8)      which is CMD's argument was out of range
    ADDR_MISALIGNED                     =    (9)      which is Misaligned address
    BLOCK_LEN_ERR                       =    (10)     which is Transferred block length is not allowed for the card or the number of transferred bytes does not match the block length
    ERASE_SEQ_ERR                       =    (11)     which is An error in the sequence of erase command occurs
    BAD_ERASE_PARAM                     =    (12)     which is An Invalid selection for erase groups
    WRITE_PROT_VIOLATION                =    (13)     which is Attempt to program a write protect block
    LOCK_UNLOCK_FAILED                  =    (14)     which is Sequence or password error has been detected in unlock command or if there was an attempt to access a locked card
    COM_CRC_FAILED                      =    (15)     which is CRC check of the previous command failed
    ILLEGAL_CMD                         =    (16)     which is Command is not legal for the card state
    CARD_ECC_FAILED                     =    (17)     which is Card internal ECC was applied but failed to correct the data
    CC_ERROR                            =    (18)     which is Internal card controller error
    GENERAL_UNKNOWN_ERROR               =    (19)     which is General or Unknown error
    STREAM_READ_UNDERRUN                =    (20)     which is The card could not sustain data transfer in stream read operation.
    STREAM_WRITE_OVERRUN                =    (21)     which is The card could not sustain data programming in stream mode
    CID_CSD_OVERWRITE                   =    (22)     which is CID/CSD overwrite error
    WP_ERASE_SKIP                       =    (23)     which is only partial address space was erased
    CARD_ECC_DISABLED                   =    (24)     which is Command has been executed without using internal ECC
    ERASE_RESET                         =    (25)     which is Erase sequence was cleared before executing because an out of erase sequence command was received
    AKE_SEQ_ERROR                       =    (26)     which is Error in sequence of authentication.
    INVALID_VOLTRANGE                   =    (27)   
    ADDR_OUT_OF_RANGE                   =    (28)   
    SWITCH_ERROR                        =    (29)   
    SDIO_DISABLED                       =    (30)   
    SDIO_FUNCTION_BUSY                  =    (31)   
    SDIO_FUNCTION_FAILED                =    (32)   
    SDIO_UNKNOWN_FUNCTION               =    (33)
    Standard errors and messages ;

    INTERNAL_ERROR                      =    (34)   
    NOT_CONFIGURED                      =    (35)   
    REQUEST_PENDING                     =    (36)   
    REQUEST_NOT_APPLICABLE              =    (37)   
    INVALID_PARAMETER                   =    (38)   
    UNSUPPORTED_FEATURE                 =    (39)   
    UNSUPPORTED_HW                      =    (40)   
    ERROR                               =    (41)   
    OK                                  =    (42)   
    CMD1_TIMEOUT                        =    (60)
    New Models and Support Page :
    • Huawei G6-U00 Full Dump package uploaded [ World First ]
    • Huawei G6-U00 Direct eMMC / ISP Pinouts uploaded
    • Huawei G6-U10 Full Dump package uploaded
    • Huawei G6-U10 Direct eMMC / ISP Pinouts uploaded
    • Huawei G700-U00 Full Dump package uploaded [ World First ]
    • Huawei G700-U00 (ISP N/A) eMMC Layout Uploaded
    • Huawei P6-T00 Full Dump package uploaded [ World First ]
    • Huawei P6-T00 Direct eMMC / ISP Pinouts uploaded
    • Huawei P6-U06 Full Dump package uploaded
    • Huawei P6-U06 Direct eMMC / ISP Pinouts uploaded
    • Nokia Lumia 610 Dump package uploaded
    • Nokia Lumia Direct eMMC / ISP Pinouts uploaded [ World First ]

    Huawei G700 :
    ISP / eMMC Pinouts are not available on the board for those who want to program eMMC
    You can still do it using eMMC Pro and connecting eMMC IC directly to eMMC Pro using the picture provided .

    Advanced eMMC Repair
    eMMC PRo - Universal Device Programmer
    Latest Threads